• Antergos Live Desktop freezes almost immediately on T480

    Thank you again!

    So graphics seem to be running all fine for the moment.

    Only my fan seems to be behaving little weird compared to Windows… (start, stop, start, stop…)
    But I am not sure if this belongs to this thread or I should rather open a new one later…

    Actually I wanted to check temperatures and ran sensors-detect in order to check temps with sensors.
    I only scanned for the first options of sensor-detectand answered “no” for the rest of the probes because the text said, it could be risky. Finally I also said no to overwrite /etc/conf.d/sensord and it showed the temps I was searching for - which seemed fine between 40-49 degrees…

    Has this changed anything permanently within my system? I am a little scared now as some sites recommend to execute it with the Default Settings (which are described as risky by the program itself though).
    Is there a way of checking if something got broken or can I just assume that it didn’t do anything?

  • should not harm your system to choose the other options, as it mostly do not find anything strange…
    But in my opinion default will show anything you need without running the detect script…

    And the of/on coicle of your fan can be related to the much less used rescources of your system when running Linux instead of windows…

  • Ok thanks, it didn’t show any errors and also after reboot shows the same output which seems pretty OK (at least no errors).

    Adapter: Virtual device
    temp1:        +35.0°C  
    Adapter: ISA adapter
    fan1:           0 RPM
    Adapter: Virtual device
    temp1:        +44.0°C  (crit = +128.0°C)
    Adapter: ISA adapter
    Package id 0:  +45.0°C  (high = +100.0°C, crit = +100.0°C)
    Core 0:        +45.0°C  (high = +100.0°C, crit = +100.0°C)
    Core 1:        +44.0°C  (high = +100.0°C, crit = +100.0°C)
    Core 2:        +45.0°C  (high = +100.0°C, crit = +100.0°C)
    Core 3:        +44.0°C  (high = +100.0°C, crit = +100.0°C)
    Adapter: Virtual device
    temp1:        +43.5°C  

    Yes, in restrospective running it ewas probably unnecessary.
    Guess I just don’t touch it anymore, just a little weird that the recommended Default options are riskier than the alternatives according to the tool tips (because of these I picked non-standard^^).
    I will just leave it as it is now, I guess.

    Thank you again for all the thorough help and clarification with the installation!!

  • @clanow said in Antergos Live Desktop freezes almost immediately on T480:


    only your fanspeed is not recognized? or does it show some rpms ?


  • this is what my TP T60 gives out without any config;

    Adapter: ISA adapter
    fan1:        2739 RPM
    temp1:        +42.0°C  
    temp2:        +35.0°C  
    temp3:        +34.0°C  
    temp4:            N/A  
    temp5:        +25.0°C  
    temp6:            N/A  
    temp7:        +25.0°C  
    temp8:            N/A  
    temp9:        +38.0°C  
    temp10:       +41.0°C  
    temp11:       +41.0°C  
    temp12:           N/A  
    temp13:           N/A  
    temp14:           N/A  
    temp15:           N/A  
    temp16:           N/A  
    Adapter: Virtual device
    temp1:        +42.0°C  (crit = +127.0°C)
    temp2:        +40.0°C  (crit = +99.0°C)
    Adapter: ISA adapter
    Core 0:       +32.0°C  (high = +100.0°C, crit = +100.0°C)
    Core 1:       +40.0°C  (high = +100.0°C, crit = +100.0°C)
  • Actually the fan speed is not always zero, but sometimes between 2700 and 3400 RPM.
    I just copied the text in the moment it turned off. (Fan runs, temperature falls to around 41, then it stops, temperature rises to 49, eventually fan starts again :)).
    I am only missing the temp values you have, though that might be because I didn’t let it scan every I/O port, maybe, I don’t know.

    I was little stupid not to test reading the sensors before running the configuration, so I guess I cannot revert it now and check what it was before, but as long as the system itself cools properly, I am happy
    (and I hope this sensor-detect did not change anything regarding cooling:)).

  • @clanow said in Antergos Live Desktop freezes almost immediately on T480:

    Finally I also said no to overwrite /etc/conf.d/sensord

    So it is the default one, as you do not save the findings.

  • Oh great ☺
    wasn’t sure if it writes any other files.

live59 freezes27 immediately3 t4801 Posts 28Views 1856
Log in to reply
Bloom Email Optin Plugin

Looks like your connection to Antergos Community Forum was lost, please wait while we try to reconnect.