• Stuck at antergOS logo while booting from liveUSB boot


    Hello everyone,

    I want to install antergOS in to my daily driver laptop but when i made my liveUSB and and booted i stuck at antergOS logo. I tried probe.blacklist=nouveau command but it didn’t worked. So please help me, I’m very curious about antergOS and I don’t want to give up.

    Sorry for my bad English.

  • Hi @Starseemer

    Could you give more information about your hardware?

    lspci -k

    ???

  • @Starseemer
    …And, if possible, the full output of

    inxi -CMGxxc0
    
  • @judd
    00:00.0 Host bridge: Intel Corporation Skylake Host Bridge/DRAM Registers (rev 08)
    Subsystem: Pegatron Skylake Host Bridge/DRAM Registers
    Kernel driver in use: skl_uncore
    00:02.0 VGA compatible controller: Intel Corporation HD Graphics 520 (rev 07)
    Subsystem: Pegatron HD Graphics 520
    Kernel driver in use: i915
    Kernel modules: i915
    00:14.0 USB controller: Intel Corporation Sunrise Point-LP USB 3.0 xHCI Controller (rev 21)
    Subsystem: Pegatron Sunrise Point-LP USB 3.0 xHCI Controller
    Kernel driver in use: xhci_hcd
    Kernel modules: xhci_pci
    00:14.2 Signal processing controller: Intel Corporation Sunrise Point-LP Thermal subsystem (rev 21)
    Subsystem: Pegatron Sunrise Point-LP Thermal subsystem
    Kernel driver in use: intel_pch_thermal
    Kernel modules: intel_pch_thermal
    00:16.0 Communication controller: Intel Corporation Sunrise Point-LP CSME HECI #1 (rev 21)
    Subsystem: Pegatron Sunrise Point-LP CSME HECI
    Kernel driver in use: mei_me
    Kernel modules: mei_me
    00:17.0 SATA controller: Intel Corporation Sunrise Point-LP SATA Controller [AHCI mode] (rev 21)
    Subsystem: Pegatron Sunrise Point-LP SATA Controller [AHCI mode]
    Kernel driver in use: ahci
    Kernel modules: ahci
    00:1c.0 PCI bridge: Intel Corporation Device 9d10 (rev f1)
    Kernel driver in use: pcieport
    Kernel modules: shpchp
    00:1c.4 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #5 (rev f1)
    Kernel driver in use: pcieport
    Kernel modules: shpchp
    00:1c.5 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #6 (rev f1)
    Kernel driver in use: pcieport
    Kernel modules: shpchp
    00:1f.0 ISA bridge: Intel Corporation Sunrise Point-LP LPC Controller (rev 21)
    Subsystem: Pegatron Sunrise Point-LP LPC Controller
    00:1f.2 Memory controller: Intel Corporation Sunrise Point-LP PMC (rev 21)
    Subsystem: Pegatron Sunrise Point-LP PMC
    00:1f.3 Audio device: Intel Corporation Sunrise Point-LP HD Audio (rev 21)
    Subsystem: Pegatron Sunrise Point-LP HD Audio
    Kernel driver in use: snd_hda_intel
    Kernel modules: snd_hda_intel, snd_soc_skl
    00:1f.4 SMBus: Intel Corporation Sunrise Point-LP SMBus (rev 21)
    Subsystem: Pegatron Sunrise Point-LP SMBus
    Kernel driver in use: i801_smbus
    Kernel modules: i2c_i801
    01:00.0 3D controller: NVIDIA Corporation GM108M [GeForce 940M] (rev a2)
    Subsystem: Pegatron GM108M [GeForce 940M]
    Kernel driver in use: nouveau
    Kernel modules: nouveau
    02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8723BE PCIe Wireless Network Adapter
    Subsystem: Realtek Semiconductor Co., Ltd. RTL8723BE PCIe Wireless Network Adapter
    Kernel driver in use: rtl8723be
    Kernel modules: rtl8723be, wl
    03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c)
    Subsystem: Pegatron RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
    Kernel driver in use: r8169
    Kernel modules: r8169
    This is the output of “lspci-k”
    @just
    inxi -CMGxxc0 is not found

  • @just said in Stuck at antergOS logo while booting from liveUSB boot:

    inxi -CMGxxc0 no se encuentra

    Install inxi con sudo pacman -S inxi

  • @judd I`m currently using debian based deepin so pacman is not works for me. Do you know the version for debian?

  • @Starseemer
    How did you try ‘probe.blacklist=nouveau’?

    1. Can you put
    modprobe.blacklist=nouveau
    

    in the kernel boot parameters list?

    1. You seem to have two graphics cards, maybe search for Optimus or bumblebee systems in Antergos wiki?
  • @Starseemer said in Stuck at antergOS logo while booting from liveUSB boot:

    @judd I`m currently using debian based deepin so pacman is not works for me. Do you know the version for debian?

    Sure, with us Debian but not the variant with Deepin.

  • Pacman help for Debian and other users:
    https://wiki.archlinux.org/index.php/Pacman/Rosetta

  • inxi may will give a more clear short output but we got enaugh info:

    • Skylake
    • Intel Corporation HD Graphics 520 + GeForce 940M (indicates bumblebee)

    you can just give us the model/manufacturer of the notebook too and we can guide you.

    [updates once a week] = [90% less problems]
    [Li{u}n//u//{i}x] since 1988 - overcoming failure means success
    howto-install-antergos
    how to add system logs
    i3 GNOME

  • @Starseemer said in Stuck at antergOS logo while booting from liveUSB boot:

    @judd I`m currently using debian based deepin so pacman is not works for me. Do you know the version for debian?

    sudo apt-get install inxi
    
  • @Starseemer
    Anyway, even without inxi it is already clear that you have Nvidia Optimus card.

    You may either follow Antergos Wiki or use the excellent nvidia-installer utility, offered by Antergos. Nvidia-installer may be used to install proprietary Nvidia drivers for both single- and double-GPU Nvidia cards (your case).

    It has only one weak point - it can’t manage BIOS settings on computers, where discrete video card is controlled by BIOS. In such a case it is possible to use this approach:

    • change BIOS settings as described in AnteWiki, in preparation to Nvidia driver installation
    • run nvidia-installer
    • change BIOS back to the original discrete video card settings

    BTW, your 940M card is reported in AnteWiki among those where Bumblebee and prop Nvidia were successfully installed on.

  • @manuel
    "How did you try ‘probe.blacklist=nouveau’?"

    when the first menu came, he pressed “e” and wrote the parameter. did he do wrong?

  • @osturk97
    That should be the correct way, but I was just wondering about the missing ‘mod’ prefix before ‘probe’. I think it should be modprobe but I’m not absolutely sure.

  • @manuel @osturk97 must be modprobe.blacklist=nouveau

    [updates once a week] = [90% less problems]
    [Li{u}n//u//{i}x] since 1988 - overcoming failure means success
    howto-install-antergos
    how to add system logs
    i3 GNOME

  • @joekamprad @manuel yeah he means modprobe.

  • @manuel said in Stuck at antergOS logo while booting from liveUSB boot:

    I think it should be modprobe but I’m not absolutely sure.

    You’re absolutely correct and you may be sure - the correct text is modprobe.blacklist=nouveau.

    A “probe.blacklist=nouveau” is just a meaningless text for a kernel, so kernel silently ignores it, without returning any error.

  • he add modprobe.blacklist=nouveau. and it didnt work so should he press any key to save this edit? or he should just press enter to open desktop.

  • [ctlr+X] as far as i know or [F10]

    [updates once a week] = [90% less problems]
    [Li{u}n//u//{i}x] since 1988 - overcoming failure means success
    howto-install-antergos
    how to add system logs
    i3 GNOME

liveusb4 booting25 logo4 stuck28 Posts 36Views 861
Log in to reply